Fender Tone Master Deluxe Reverb Firmware Updates
Owners of Tone Master Deluxe Reverb amplifiers now have the ability to update their amplifiers with modified firmware that can enhance playability for some users. No update is necessary unless one of the modified versions is desired. Stock firmware as shipped from the factory is also available below.
System Requirements:
- Windows 10 and higher
- macOS X 10.7 and higher
Release Notes:
ToneMaster_Deluxe_VintageSpec_1.0.27
- Vintage accurate firmware based on vintage and 65 Reissue tube amplifiers.
- Stock firmware loaded on Tone Master Deluxe Reverb amplifiers with Jensen N12K speaker.
- Jensen N12K speaker line out IRs captured with Shure SM57 and Royer 121 microphones.
Tone Master Deluxe Reverb: Vintage Spec Firmware v1.0.27
ToneMaster_Deluxe_RvbMod_1.1.35
- Modified reverb control for easier fine tuning at lower settings.
- Jensen N12K speaker line out IRs captured with Shure SM57 and Royer 121 microphones.
Tone Master Deluxe Reverb: Reverb Mod Firmware v1.1.35
ToneMaster_Deluxe_RvbMod_NoBrightCap1.1.35
- Modified reverb control for easier fine tuning at lower settings.
- No bright cap on vibrato channel for smoother treble response when using overdrive and distortion pedals at lower settings.
- Jensen N12K speaker line out IRs captured with Shure SM57 and Royer 121 microphones.
Tone Master Deluxe Reverb: Reverb Mod No Bright Cap Firmware v1.1.35
ToneMaster_Blonde_Deluxe_RvbMod_1.1.35
- Modified reverb control for easier fine tuning at lower settings.
- Celestion Neo Creamback speaker line out IRs captured with Shure SM57 and Sennheiser MD 421 microphones.
Tone Master Blonde Deluxe Reverb: Reverb Mod Firmware v1.1.35
ToneMaster_Blonde_Deluxe_RvbMod_NoBrightCap1.1.35
- Modified reverb control for easier fine tuning at lower settings.
- No bright cap on vibrato channel for smoother treble response when using overdrive and distortion pedals at lower settings.
- Celestion Neo Creamback speaker line out IRs captured with Shure SM57 and Sennheiser MD 421 microphones.
Tone Master Blonde Deluxe Reverb: Reverb Mod No Bright Cap Firmware v1.1.35
- Download and unzip desired firmware version at the top of this article.
- Locate the micro-USB port and firmware update button on the underside of the amplifier chassis beneath the OUTPUT POWER section.
- Power on the amplifier while holding the firmware update button for at least 3 seconds.
- Once booted (approximately 10-15 seconds), the firmware update LED next to micro-USB port will slowly blink to indicate that the amp is in firmware update mode. The power jewel located on the front of the chassis will also cycle between amber and red.
- Connect a USB data cable from the Tone Master amplifier to your MAC or PC. USB Charging cables may not work if data lines are not connected.
- The amplifier will appear on your computer as a mass storage device named FENDER_AMP (similar to USB flash and external hard drives)
- Drag and drop the firmware update .img file onto the FENDER_AMP folder.
- The Update LED will blink quickly to indicate the update is being applied, this process should continue for approximately 30-60 seconds.
- Once the update has completed successfully the firmware update LED will stop blinking and remain ON and the amplifier will auto eject from the computer. Note some MAC user may receive a Disk Not Ejected Properly message. This is normal and not an error.
- If update was successful, disconnect the USB cable and power cycle the amplifier to return to normal operation.
- If the update was unsuccessful, the firmware update LED will stop blinking and remain OFF. Power cycle the amplifier and repeat update procedure beginning at step 3.